Grass-valley iTX Output Server 2 v.2.5 Manual de usuario Pagina 1

Launch GuideiTX v2.520 April 2015iTX Output Server 2Next Generation Video Engine

6Preparing for Output Server 2Required System ConfigurationRequired System ConfigurationFeature RequirementVertigo XG Inside When XG Inside is enabled

7iTX Output Server 2Launch GuideUpgrading from Output Server 1 to Output Server 2iTX allows broadcasters to transition from an Output Server 1 system

8Preparing for Output Server 2Upgrading from Output Server 1 to Output Server 2

9Installing and Starting Output Server 2This chapter discusses how to install or upgrade the Output Server 2 service and related components and how t

10Installing and Starting Output Server 2Transitioning to Output Server 2Below are some guidelines for operating a mixed Output Server system during t

11iTX Output Server 2Launch Guide10 Route newly commissioned Output Server 2 master channel to air.11 Failover the Output Server 2 slave, so the chann

12Installing and Starting Output Server 2Upgrading to the Output Server 2 ServiceUpgrading to the Output Server 2 ServiceBefore upgrading a playout se

13iTX Output Server 2Launch GuideConfirming your current versionYou can confirm which version of Output Server and TX Play you are running from the iT

14Installing and Starting Output Server 2Starting Output Server 2

15Setting Up Output Server 2This chapter explains how to configure an Output Server 2 channel using the Configuration panel on the Output Server 2 us

iiNoticesCopyright and Trademark NoticeCopyright © 2014, Grass Valley, A Belden Brand. All rights reserved.Belden, Belden Sending All The Right Signal

16Setting Up Output Server 2Accessing the Output Server 2 User InterfaceAccessing the Output Server 2 User InterfaceTo access the Configuration and En

17iTX Output Server 2Launch Guide2 To set the format and frame rate for the channel, select a value from the Resolution drop-down list (e.g. 720p 50.0

18Setting Up Output Server 2Configuring the Nielsen WatermarkConfiguring the Nielsen Watermark The Nielsen watermark is an inaudible cue tone in the a

19iTX Output Server 2Launch Guide•Program Content•Final Distributor• Unknown Distribution8Click Save to store your changes and automatically reboot th

20Setting Up Output Server 2Configuring Audio Mapping2 Select a Dolby output group from the Audio Output field.Note: Clicking Reset will revert the va

21iTX Output Server 2Launch Guide7 On the first track, click the Audio Type drop-down list and select the required type (e.g. Dolby D 5.1)When selecti

22Setting Up Output Server 2About the SCTE104 pluginAbout the SCTE104 pluginThe SCTE104 plugin supports the following enhanced features:• The ability

23iTX Output Server 2Launch Guide3 To enable the passing of null SCTE messages for heartbeating to downstream services, click Heartbeat Enabled. This

24Setting Up Output Server 2Configuring SCTE104 Features• If you want the channel to process spliceStart_immediate insert commands,enable Immediate Se

25iTX Output Server 2Launch GuideConfiguring the SCTE104 Message TypesIn addition to the configuration that has to be performed in the Output Server 2

1Table of Contents1 Introducing Output Server 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1About Output Server 2. . . . . . . . . . .

26Setting Up Output Server 2Configuring Basic Subtitle Setup•In Event Editor for the sequence item: • Specify the sequence’s availability window by en

27iTX Output Server 2Launch Guide2Expand the Stream section.3Click Add. An Add Stream window appears.4 Enter the new stream name in the Stream Name fi

28Setting Up Output Server 2Creating a Subtitle ServicesCreating a Subtitle ServicesServices can be for an open or closed subtitle. Each closed subtit

29Operation and MaintenanceThis appendix contains information about day-to-day operation and maintenance of Output Server 2 and supporting services.

30Operation and MaintenanceServer Controller Configuration for Output Server 24Make sure Enabled is checked. This will run the instance of the service

31iTX Output Server 2Launch GuideViewing the Output Server 2 Engineering PanelAlong with the Configuration panel, Output Server 2’s user interface inc

32Operation and MaintenanceEvent Log TabEvent Log TabThe Event Log displays events sent from FPP to Output Server 2. This information can be used by G

33iTX Output Server 2Launch GuideLog Files for Output Server 2The log files for Output Server 2 can be found in the following locations:Component Logs

34Operation and MaintenanceDowngrading from Output Server 2 to Output Server 1Downgrading from Output Server 2 to Output Server 1It is possible to dow

Contact UsGrass Valley Technical SupportFor technical assistance, contact our international support center, at1-800-547-8949 (US and Canada) or +1 51

2Table of ContentsConfiguring sequences for SCTE104 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25Configuring

1Introducing Output Server 2This guide describes the features and functionality of Output Server 2 (OS2), the differences between Output Server 2 and

2Introducing Output Server 2Output Server 1 and Output Server 2 ComparisonOutput Server 1 and Output Server 2 ComparisonThe table below details the di

3iTX Output Server 2Launch GuideKnown Limitations of Output Server 2Output Server 2 has the following known limitations:• Automatic Loudness Control (

4Introducing Output Server 2Known Limitations of Output Server 2

5Preparing for Output Server 2This chapter discusses the hardware and software prerequisites for operating an Output Server 2 iTX system, including t