Grass-valley Kaleido Remote Control Protocol Gateway Jan.09 201 Manual de usuario

User’s GuideM770-0900-1169 January 2014

6Gateway CommandsDocument ConventionsDocument ConventionsEach command in this document is presented in the following format:Command NameApplicable Kal

7Kaleido Remote Control Protocol (Gateway)User’s GuideGateway Command DescriptionsThe syntax must be exactly replicated when sending a command. Use th

8Gateway CommandscloseID• The system name was invalid.•The IP address was wrong.closeIDKX K2 AQ This command closes a session with the specified Kalei

9Kaleido Remote Control Protocol (Gateway)User’s Guide<getKCurrentLayout/>Gateway response:• For a Kaleido-Alto/Quad/Quad-Dual multiviewer:<k

10Gateway CommandsgetKLayoutListgetKLayoutListKX K2 AQ This command returns the list of layouts that are available on the multiviewer.<getKLayoutLi

11Kaleido Remote Control Protocol (Gateway)User’s Guide<preference editable="false" editablePerUser="true" type="useLargeC

12Gateway CommandssetKUnlatch<setKStatusMessage>set id="ID" status="Status" message="Message" </setKStatusMessa

13Kaleido Remote Control Protocol (Gateway)User’s GuideExample: <setKUnlatch>set id="my_gateway_alarm_1"</setKUnlatch>Gateway re

14Gateway CommandssetKDynamicTextcomposite42. The monitor name is the name you see (under Assignments in the Properties tab) when you open the layout

15Kaleido Remote Control Protocol (Gateway)User’s GuidegetKMetaDataK2 This command is used to get metadata that is assigned to a MultiData component a

iiNoticesCopyright & Trademark NoticeCopyright © 2006–2014, Miranda Technologies Partnership. All rights reserved.Belden, Belden Sending All The R

16Gateway CommandssetKTimer• timeZoneThe value field is escaped as defined in the XML protocol for an attribute value. For example, ABC"DEF\GHI&l

17Kaleido Remote Control Protocol (Gateway)User’s Guideshould be counting or waiting to start when it compares the start time to the current time.• NO

18Gateway CommandsgetKActionListWhere NameOfTheActionToFire is the friendly name of the action to be executed.Gateway response:• <ack/>: The com

19Kaleido Remote Control Protocol (Gateway)User’s GuideWhere NameOfTheGroupToDisable is the name of the alarm group (for a Kaleido-K2 multiviewer), or

20Gateway CommandssetKAudioOut• For an Audio Bridge Terminal (ABT) source, the returned value indicates which ABT input is being monitored:<kAudioO

21Kaleido Remote Control Protocol (Gateway)User’s Guide• 999.999.999.999 is the IP address of the device from where the stream occurs.• XX is the iden

22Gateway CommandssetKAudioOutVolumesetKAudioOutVolumeKX K2 AQThis command sets the volume at the analog audio monitoring output.<setKAudioOutVolum

23Kaleido Remote Control Protocol (Gateway)User’s GuidesetKAudioOutModeKX K2 AQTo set the audio monitoring mode at the analog audio monitoring output,

24Gateway CommandssetKMouseColorB<setKMouseColorA>set mouseColorA="FFBBGGRR"</setKMouseColorA>Where FFBBGGRR is the hexadecimal

25A Typical SessionHere is a description of how to open and close a typical session during which you will use the Gateway commands to operate a Kalei

iiiTable of Contents1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1Software Versions . . . .

26A Typical SessionOpening an HyperTerminal SessionTo establish the HyperTerminal session with the multiviewer1In Connection Description, type a name

27Kaleido Remote Control Protocol (Gateway)User’s Guide5Click OK.To be able to see the characters you type in the HyperTerminal console1On the File me

28A Typical SessionOpening a Gateway Session With a MultiviewerOpening a Gateway Session With a MultiviewerTo open a Gateway session with a multiviewe

29Kaleido Remote Control Protocol (Gateway)User’s Guide

31Kaleido-X Series Support HistoryFor each Kaleido Remote Control Protocol (Gateway) command, the following table indicates, for each Kaleido-X serie

32Kaleido-X Series Support HistorygetKAudioOutMode 3.00 4.10 — — 7.00setKAudioOutMode 3.00 4.10 — — 7.00setKVerticalOffset N.A. N.A. N.A. N.A. N.A.set

Contact UsMiranda Technical SupportFor technical assistance, please contact the Miranda Technical Support center nearest you:Corporate Head OfficeMira

1IntroductionKaleido-K2, Kaleido-Alto/Quad/Quad-Dual, Kaleido-X, Kaleido-X16, KMV-3901/3911, and Kaleido-IP multiviewers can execute commands receive

2IntroductionGateway Options for the Kaleido-K2In an environment containing many Kaleido-K2 multiviewers, there is a gateway running on each Kaleido-K

3Kaleido Remote Control Protocol (Gateway)User’s Guide4On the File menu, click Save to save your changes.5Close Notepad.6 Restart the Kaleido-K2.Kalei

5Gateway CommandsKaleido multiviewers support the following commands through the Gateway access. Most of these apply to all Kaleido multiviewer model